Horror Stories of Metallic Epoxy

Administrator — Sat, 29 Jun 2019 21:16:45 +0000

Horror Stories of Metallic Epoxy

Unskilled Metallic Epoxy Installers

the horror Stories of Metallic Epoxy include two key, this is a clear base and powder. They mix to form a blend, producing a glossy, nice look effect after complete. Shop here and check out our other services here.

Pour over the Bathroom, or solid top. They move through the floor as it cures and can with a paintbrush or roller to create effects such as swirls, ripples, craters, or waves. When the Bathroom hardens, these powders are in place, resulting in a beautiful, nice look.

Each epoxy Bathroom is special due to the nature of the powder holding. Skill and mind are critical to achieving the appearance and feel of the surface.

Metallic Epoxy Bathroom include two key, this is a clear base and powder. They mix to form a blend, producing a glossy, nice look effect after complete.

The bathroom design ideas, or solid top. They move through the floor as it cures and can with a paintbrush or roller to create effects such as swirls, ripples, craters, or waves. When the Epoxy hardens, these powders are in place, resulting in a beautiful, nice look.

Our Bathroom is special due to the nature of the powder holding. Skill and mind are critical to achieving the appearance and feel of the surface.

Metallic Epoxy Advantages

Epoxy Bathroom include two key, this is a clear base and powder. They mix to form a blend, producing a glossy, nice look effect after complete.

Room interior, or solid top. They move through the floor as it cures and can with a paintbrush or roller to create effects such as swirls, ripples, craters, or waves. When the Bathroom hardens, these powders are in place, resulting in a beautiful, nice look.

Interior

Each epoxy Bathroom is special due to the nature of the powder holding. Skill and mind are critical to achieving the appearance and feel of the surface.

Metallic Epoxy Bathroom include two key, this is a clear base and powder. They mix to form a blend, producing a glossy, nice look effect after complete.

Pour over the Metallic Epoxy Advantages, or solid top. They move through the floor as it cures and can with a paintbrush or roller to create effects such as swirls, ripples, craters, or waves. When the Epoxy hardens, these powders are in place, resulting in a beautiful, nice look.

Our Bathroom is special due to the nature of the powder holding. Skill and mind are critical to achieving the appearance and feel of the surface.

Metallic Design

Epoxy Bathroom include two key, this is a clear base and powder. They mix to form a blend, producing a glossy, nice look effect after complete.

Space

Each epoxy Bathroom is special due to the nature of the powder holding. Skill and mind are critical to achieving the appearance and feel of the surface.

Metallic interior includes two key, this is a clear base and powder. They mix to form a blend, producing a glossy, nice look effect after complete.

Over the design, or solid top. They move through the floor as it cures and can with a paintbrush or roller to create effects such as swirls, ripples, craters, or waves. When the Epoxy hardens, these powders are in place, resulting in a beautiful, nice look.

Our Bathroom is special due to the nature of the powder holding. Skill and mind are critical to achieving the appearance and feel of the surface.

Metallic Epoxy Design

Epoxy design include two key, this is a clear base and powder. They mix to form a blend, producing a glossy, nice look effect after complete.

Pour over the living room, or solid top. They move through the floor as it cures and can with a paintbrush or roller to create effects such as swirls, ripples, craters, or waves. When the Bathroom hardens, these powders are in place, resulting in a beautiful, nice look.

Each epoxy Bathroom is special due to the nature of the powder holding. Skill and mind are critical to achieving the appearance and feel of the surface.

Metallic Epoxy interior includes two key, this is a clear base and powder. They mix to form a blend, producing a glossy, nice look effect after complete.

Space

Pour over the Art Panel, or solid top. They move through the floor as it cures and can with a paintbrush or roller to create effects such as swirls, ripples, craters, or waves. When the Epoxy hardens, these powders are in place, resulting in a beautiful, nice look.

Our Bathroom is special due to the nature of the powder holding. Skill and mind are critical to achieving the appearance and feel of the surface.

Unskilled Metallic Epoxy Installers

Design include two key, this is a clear base and powder. They mix to form a blend, producing a glossy, nice look effect after complete.

Our epoxu or solid top. They move through the floor as it cures and can with a paintbrush or roller to create effects such as swirls, ripples, craters, or waves. When the Bathroom hardens, these powders are in place, resulting in a beautiful, nice look.

Each epoxy Bathroom is special due to the nature of the powder holding. Skill and mind are critical to achieving the appearance and feel of the surface.

Design Space

Metallic Epoxy includes two key, this is a clear base and powder. They mix to form a blend, producing a glossy, nice look effect after complete.

The Minimalist Home Design interior move through the floor as it cures and can with a paintbrush or roller to create effects such as swirls, ripples, craters, or waves. When the Epoxy hardens, these powders are in place, resulting in a beautiful, nice look.

Our interior is special due to the nature of the powder holding. Skill and mind are critical to achieving the appearance and feel of the surface.

Metallic Epoxy for Metallic Epoxy Advantages

Epoxy Interior design include two key, this is a clear base and powder. They mix to form a blend, producing a glossy, nice look effect after complete.

Bathroom design ideas or solid top. They move through the floor as it cures and can with a paintbrush or roller to create effects such as swirls, ripples, craters, or waves. When the Bathroom hardens, these powders are in place, resulting in a beautiful, nice look.

Each Unskilled Metallic Epoxy Installers is special due to the nature of the powder holding. Skill and mind are critical to achieving the appearance and feel of the surface.

How to Distinguish between Professional Metallic Epoxy Installers from the Unskilled | Horror Stories of Metallic Epoxy

With interest in Metallic Epoxy Interiors and installations are gaining traction every day. More and more Metallic Epoxy Installers are popping up in the market. How do you tell the professionals from the simply unskilled?

In this article, we list the key mistakes, as well as the tell-tale signs, which may help you differentiate and assist you in your decision to picking the right installers.

Sometimes, epoxy which is meant to help solve a problem such as a cracked countertop, becomes the problem itself.

Introduction | Horror Stories of Metallic Epoxy

Like every other product and service, Metallic Epoxy is offered by a variety of suppliers. Some individual contractors, others larger firms.

Today’s post seeks not to evaluate either source, but rather to give you the tools to distinguish good workmanship from bad. For ease of reference, these telltale signs of poor work will be listed in ascending order. From mere eyesore to catastrophic malfunction.

Metallic Epoxy is so difficult to manipulate, and design is extremely subjective. So here we have a gorgeous Blue Galaxy Themed Metallic Epoxy Flooring done by us!

1. Poorly Manipulated Patterns Or Designs (For Flat Surfaces) | Horror Stories of Metallic Epoxy

Imagine having chosen an exotic-patterned Metallic Epoxy Floor for your bathroom, with bold golden streaks accenting a jet-black background. You return home, after the installation, to find that the design of your floor has fallen incredibly far off its mark.

The broad golden swirls are little more than vague patches of gold pigments. Vast stretches of empty black space between the gold accents mirror the expanse between reality and expectation. This is nothing like the catalogue, you scream in your head.

Poor Execution

While poor execution of the intended design doesn’t directly compromise the integrity of the floor. It does cast doubt on the contractor’s ability to deliver on any other prior promises.

You’d better start running down this list and checking your floor.

2. Bubbles | Horror Stories of Metallic Epoxy

Bubbles are fun in the air, they are great in your drinks. However, they are neither fun nor great when they’re in your Metallic Epoxy Floor.

These small defects within the Metallic Epoxy are usually due to one of three factors. Improper pouring and spreading of product, tiny particulate within the epoxy, and outgassing from concrete / pororus floors.

While the first is a strong sign of an amateur installer. The second could indicate poor pre-installation cleaning or inter-installation contamination. Lastly, the third factor is rather debatable in terms of culpability.

Outgassing

Outgassing occurs when the air in cement / porous substrate rises and gets trapped in the Metallic Epoxy layer above it. The amount of air released from cement / porous substrate is dependent on the type of cement mix/material used to construct the floor.

This is a factor that is out of the Metallic Epoxy Installer’s control. However, any installer worth his salt is fully aware of outgassing. They also understand the importance of applying a layer of sealant and primer below the epoxy to greatly minimise any outgassing.

Small bubbles that pop resulting in holes and craters in your finished Metallic Epoxy surface

Microscopic bubbles such as these on the edge caused by natural warm climate or the difference between the epoxy and surface temperature is considered within industry standards.

3. Stains | Horror Stories of Metallic Epoxy

Since Metallic Epoxy is a non-porous material and can’t actually be stained. The term ‘stain’ is a bit of a misnomer.

The hideous ‘water stains that most homeowners see on poorly installed Metallic Epoxy Surfaces are largely due to two reasons. Moisture trapped within the cured Metallic Epoxy, or the epoxy is partially peeling off the surface it was applied on.

The former is usually due to improper pre-installation surface preparations. While the latter is commonly the result of using a low-quality substrate that epoxy does not adhere properly to.

Professional installers ensure proper surface prep is done. They also employ one or more sealant and primer layers to further reduce moisture and increase the epoxy’s adhesion.

Metallic Epoxy is a non-porous and seamless material, which results in it being stain- and waterproof! But cheap material and poor application can result in oil stains as seen above.

4. Uneven Surface | Horror Stories of Metallic Epoxy

The average Metallic Epoxy mix takes just over an hour to cure. Ample time for the capable installer to finish arranging patterns within the epoxy and smooth it over.

Such a simple process is another matter entirely for inexperienced or inefficient contractors. Examples include taking too long to finish the pattern arrangement. It also means less time to smooth the Metallic Epoxy over before it fully cures.

This results in a rushed job and a highly uneven surface. While applying a topcoat helps to even out minute irregularities, larger dips and rises cannot be removed entirely. These dips may trap food or shallow puddles of liquids in which bacteria or mould can grow, while making it more difficult to clean than a smooth and regular surface.

Unskilled Metallic Epoxy application resulting in uneven and non-levelled finish.

Craters caused by bubbles poorly covered up with a sloppy, additional layer of epoxy

5. Mould | Horror Stories of Metallic Epoxy

The primary cause of mould on a mould-free material is the installer error. In much the same way as Horror Number 2. Subpar surface preparation and cutting corners on applying a sealant and primer layer can allow moisture to penetrate from beneath the Metallic Epoxy layer.

On its own, this allows mould to grow in isolated colonies under the Metallic Epoxy surface, but not extensively. However, coupled with the cracks, fissures and many bubbles in a poorly installed Metallic Epoxy. The mould has free reign to spread throughout the flooring, sometimes even reaching the surface.

Such damage can only be repaired at great cost. This includes, hacking out the entire affected section and reinstalling as a whole. Often times, the damage is so extensive that it’s simply more economical to remove and reinstall everything.

One of the many key advantages of Metallic Epoxy being non-porous and seamless, allowing it to be stain- and waterproof. However, cheap and low-grade quality epoxy can result in mould as seen above.

6. Warping | Horror Stories of Metallic Epoxy

Warping is often due to poor adhesion between the Metallic Epoxy and its substrate at a critical part of the application process, curing.

As Metallic Epoxy cures, it contracts by a very small amount. Across a large space, this can add up, causing the Metallic Epoxy layer to pull up and away from spots that it poorly adheres to in dramatic fashion.

The results are obvious, exposed bare floor and a highway beneath the Metallic Epoxy for bacteria and mould to fester. While one reason for such poor adhesion is simple, poor surface preparation and cleanliness before and during installation. The other is a little more obscure. The surface that Metallic Epoxy is laid on has to either be coated with primer for good adhesion or be a surface that naturally sticks with Metallic Epoxy.

Unsuitable Surfaces

Some surfaces that are poor matches include sealed concrete or flooring with layers of polish or anti-stick material. An amateur installer who skips the surface preparation & primer layer doesn’t check for such surfaces, resulting in a warped Metallic Epoxy.

Fortunately, warping occurs right as the Metallic Epoxy is curing, giving you ample time to dispute the issue with your installer and seek redress. Still, an unusable surface rates this horror pretty high on the list.

Skipping even one step in the whole process can lead to a warped countertop above.

7. Peeling | Horror Stories of Metallic Epoxy

This is the greatest sin of all, a point at which you would be better off with a naked surface. Due to catastrophically poor adhesion across the entire Metallic Epoxy layer, it begins to peel right off the substrate while remaining in one solid sheet.

Common areas where this happens

This problem is most notable at the edges of bathroom walls or the edge of a countertop facing a sink. It is where water and organic debris will enter and fester beneath the Metallic Epoxy layer.

If your installer installed a nice, clear coating. You would have a front-row seat to watch the mould bloom beneath the Metallic Epoxy while being entirely unable to clean it up.

Why is this the worst horror

The main reason peeling Metallic Epoxy is such a grave horror is because it may only be observed weeks after installers hand over the project. At which point shady contractors may refuse to perform repairs.

Unlike warping, your only options are probably a full installation by another contractor. The reasons for such poor adhesion are similar to those in Horrors Number 1 through 6. Improper pre-installation Surface Prep & Cleaning, Low Quality Substrate, and Improper Mixing of the Metallic Epoxy Product.

Skipping on the necessary steps and using low-grade products reduce turnover time and costs are just some of the things installers may resort to in order to obtain a low price point. Metallic Epoxy peeling as seen in the image above is a sitting time-bomb waiting for mould, dirt and bacteria to fester and grow.

Red Flags / Tell-Tale Signs of an Unskilled Installer

While it is useful to be able to evaluate the quality of your installed Metallic Epoxy Interior. Few would argue that it would be infinitely more useful and less expensive to be able to tell a good contractor from a bad one.

Credibility

Some of the best ways to find a good contractor are client reviews. Facebook, Instagram, Google. These are indispensable resources for the careful homeowner, and precious currency for business owners.

Frauds

The first sign to watch for is possible fraudulent social media material. Shadier contractors tend to get stock photos from industrial sources and insinuate that the installations in the photos are past projects of theirs.

If you notice suspiciously similar photos across a few contractors, the odds are that one or more of them are not being honest.

Observe their Past Projects

The next sign is simply using what you’ve learnt about the seven horrors and observing photos that the contractor’s post. Despite posting only the least incriminating photos, bad contractors are typically unable to avoid showing defects in their installed Metallic Epoxy Interiors.

Poorly executed design (horror #1) and an uneven or scratchy surface (horror #4) are the easiest to spot, besides bubbles.

Surprisingly Low Prices

The final sign is cost. You often get what you pay for. While expensive services can sometimes turn out to be disappointing, it is more often the case when deals that are too good to be true prove the rule.

Shop for quotes across different contractors. If a contractor offers a surprisingly low price for services, further digging often turns up skeletons.

Conclusion | Horror Stories of Metallic Epoxy

With these tools at your disposal, we hope that it’ll be easier for you to hire a good contractor and get what you pay for.

To view our works and testimonials from satisfied clients, look no further than our Facebook page and our testimonial page. For an obligation-free, all-you-can-ask consultation with our experts, feel free to drop a message or call us for an appointment.

Disclaimer

With all those said, do note that Metallic Epoxy is volatile, and as it is hand-drawn, it takes skill and experience to manipulate and create the designs and effects requested by clients.

Environment as well as a key factor; the closer to a “clean-room” environment the Metallic Epoxy application is installed in, the better the finishing product. The type of surface, the levelness, and the working conditions all affect the outcome of the finishing look and feel as well.

Minor variations, be it in colour or design outlook from the proposed samples, or natural occurrences such as dust spots or minor spots due to the metallic pigments, may happen in any project and should be accepted if within industry standards.

Check out our FAQs for more information on the technical and design aspects!

More information which you may find useful

1) Project by Inexperienced Contractors – Click HERE

2) View our Past Works – Click Here

3) Metallic Epoxy Floorings – Click Here

4) Metallic Epoxy Art Panels – Click Here

5) Metallic Epoxy Countertops – Click Here

6) Metallic Epoxy Bathroom – Click Here